Skip to content

DT Swiss EX 471 26" spoke length

ERD 537 mm, made in 32 hole. Pick your hub in the calculator for your exact spoke lengths.

Rim

ERD 537 mm, made in 32 hole.

Sizes from DT Swiss's own website. Rims change, so check the ERD on yours or on the maker's page.

Some alloy rims use them. Leave empty if you don't.

How to measure ERD yourself
gapspoke + nipple,screwed on flushERD = spoke + spoke+ gap

Take two spokes of a known length and screw a nipple onto each until the thread end is flush with the top of the nipple. Drop them through opposite spoke holes so the nipples sit in the rim as they would in a built wheel. Pull them tight towards each other and measure the gap between the bent ends. ERD is the gap plus both spoke lengths.

Hub

J-bend. Flange diameter 57 / 59 mm, centre to flange 32 / 19.6 mm (left / right).

Hub not listed? Choose "Type in my hub", or tell me which one and I'll add it.

Lacing

Crosses, left (disc side)

Crosses, right (drive side)

I've started you on 3-cross for 32 hole, which suits most wheels. Radial is only for a side that doesn't brake or drive: a rim-brake front, or the non-drive side of a rim-brake rear.

Left sideRight side
Spokes

Used for the stretch, the weight and the ping note.

Most wheels 100 to 130. Check your rim's limit.

Spoke lengths

Check your rim and hub against the maker's sizes before you order spokes.

Rear wheel, 32 hole, J-bend spokes, 537 mm ERD.

SideSpokesLength
Left (disc side)3-cross16260 mm259.6 worked out
Right (drive side)3-cross16258 mm258.1 worked out

Rounded to the nearest mm. Between two sizes, go for the shorter one.

Tension: the left spokes run at 62% of the right side's tension. Bracing angles 7.1° left, 4.4° right.

Weight: these spokes and alloy nipples come to about 188 g (about 209 g with brass nipples).

Ask me to build it

Order these spokes from me

32 spokes and nipples, about £43.20 before postage. I'll email you to confirm the price and postage before you pay anything.

Email me this list
Save to My Shed
Will my spokes fit?
Ping tuner: what each side should sound like
C5, about 509 Hz at 68 kgf
E5, about 659 Hz at 110 kgf

Pluck each spoke between the rim and where it last crosses another, and match the note. Every spoke on one side should sound the same. It's a guide to even tension by ear, not a tension meter.

Often needed with this wheel

  • A Garbaruk cassette

    Lightweight 10-52 and 10-44 options for XD, MicroSpline and HG freehubs.

  • Nextie carbon rims

    Every Nextie rim is in this calculator too, and I can build any of them into a wheel for you.

These lengths come from the makers' published sizes and a standard sum. Rims and hubs vary from batch to batch, and sizes you put in yourself are only as good as your measuring. Travers Bikes takes no responsibility for spoke lengths worked out with this calculator, or for spokes, wheels or parts bought or built using them.

DT Swiss EX 471 26" with common hubs

J-bend lengths include the bend; straight-pull lengths include the hub maker's spoke offset. Rounded to the nearest mm.
HolesLeftRightLacing
Hope Pro 5 Boost front 110mm, 6-bolt32259 mm261 mm3-cross
Hope Pro 5 Boost rear 148mm, 6-bolt32260 mm258 mm3-cross
DT Swiss 240 EXP Boost front 110mm, Centrelock32261 mm263 mm3-cross
DT Swiss 240 EXP Boost rear 148mm, Centrelock32261 mm260 mm3-cross
Shimano Deore XT HB-M8210 front 110mm, Centrelock32261 mm262 mm3-cross
Shimano Deore XT FH-M8210-B rear 148mm, Centrelock32260 mm258 mm3-cross
SON 28 15x110 Boost, Centrelock32259 mm259 mm3-cross

Back to the spoke length calculator for how it works and how to measure your own parts.

A pair of Nextie carbon wheels built at Travers Bikes

Want me to build it?

I hand-build wheels in Rochford with Nextie carbon rims and Hope, DT Swiss, Chris King, Shimano, Nextie and SON hubs. I work out the spokes and order them, so getting the length right is my job, not yours.

Price a wheel build
BookMy Shed