Skip to content

Tyres and tubes 4.07

Tubeless upkeep

Tubeless isn't fit and forget. Sealant dries out, valve cores clog and some holes are too big for sealant to close. A few minutes every couple of months keeps it working, and a plug kit gets you home when it doesn't.

Get the printable PDF
DRIED SEALANTlumps that don't seal anythingLIQUID SEALANTthe bit that does the workPLUGfor holes sealant can't closeBEADa burp lets air out hereTRAVERSCanewdon, Essextraversbikes.comTUBELESS UPKEEPGUIDE 4.07 · SIZES IN MM · NOT TO SCALE
A tubeless tyre cut in half: liquid sealant, dried lumps and a plug in the tread. Drawing not to scale.

The three jobs

PUSH IN, PULL THE TOOL OUT

Plug a hole

Push a plug into the hole with the tool, pull the tool out, pump up and ride.

CORE OUT, SYRINGE IN

Top up

Valve core out, syringe on, sealant in, core back. No need to take the tyre off.

SHAKE IT: NO SLOSH, NO SEALANT

Check it

Shake the wheel by your ear. If you can't hear sealant sloshing, it needs more.

Every couple of months

  1. Shake each wheel by your ear. No slosh means the sealant has dried. Silca say refresh it every 6 months.
  2. Top up through the valve. Turn the valve to the top, core out, sealant in with a syringe, core back, pump up.
  3. Once a year, take the tyre off and peel out the dried sealant. It adds weight and stops new sealant spreading.
  4. Clean or swap the valve cores when air goes in slowly or not at all. Dried sealant blocks them.

When it goes wrong

ProblemFix
Small hole spitting sealantTurn the hole to the bottom and ride on; it usually seals
Hole that won't sealA plug, then top up the air
Cut in the sidewallA tyre boot and a tube to get home; then a new tyre
Burp: air lost at the rim in a cornerPump it up and check the pressure isn't too low
Tyre slowly goes downTop up sealant, check the valve and the tape

How much

TyreTop up
Roadabout 30 ml
Gravelabout 40 ml
MTBabout 60 ml

Or empty it and refill: traversbikes.com/tyre-fit

Tools

  • Plug kit (and spare plugs)
  • Valve core tool
  • Sealant syringe
  • Spare valve cores
  • Tyre boot and a spare tube

Things that catch people out

  • Mixing sealants can turn them to rubbery lumps. Stick to one, or clean the old one out first.
  • Cold weather slows sealant down. It seals less well below freezing.
  • A plug needs pressure to hold. Pump up straight after and check it again at home.
  • Too low a pressure burps. Tubeless runs lower, but not so low the bead lifts in corners.

From the workshop

Put a bit of tape on the rim with the date you last topped up the sealant. It saves guessing. If you'd rather I did it, I can refresh the sealant while the bike's in for a service.

Michael

Book it in

Tubeless parts in the shop

See them all

Not sure which fits? Send us your bike's make, model and year and we'll tell you.

Get the printable PDF

The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.

We'll email you a link. It unlocks every guide on that device.

Already unlocked on this device? Download the PDF

This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against Silca's and Squirt's sealant advice.

BookMy Shed