Skip to content

Forks and cockpit 2.06

Spacers and stack height

The spacers under your stem set how high your bars are. Moving them is the easiest change to your position you can make, and it costs nothing. There are a few rules, though, especially on carbon forks.

Get the printable PDF
SPACERS3TOP CAPSTEERER 3 MM BELOWthe top of the stemSPACERSunder the stem raise the barsHEAD TUBECARBON STEERERS: A MAXIMUMoften 30 to 40 mm, check the fork makerTRAVERSCanewdon, Essextraversbikes.comSPACERS AND STACK HEIGHTGUIDE 2.06 · SIZES IN MM · NOT TO SCALE
A steerer cut in half through the stem and spacers. Drawing not to scale, sizes in millimetres.

Three set-ups

ALL SPACERSUNDER: BARS UP

All spacers under the stem

Bars as high as they'll go on this steerer. A good place to start.

SPACERS ABOVE:BARS LOWER

Some spacers on top

Bars lower. The steerer must still reach most of the way up the stem.

CUT LINE

Cutting the steerer

Once you're sure of the height, the steerer can be cut so it sits 3 mm below the top of the stem.

Moving spacers

  1. Undo the stem bolts, then the top cap. Hold the front wheel between your knees so the fork doesn't drop out.
  2. Slide the stem off and move the spacers above or below it. Line the stem up with the wheel and put it back on.
  3. Set the bearing preload with the top cap: just enough that there's no knock when you rock the bike with the front brake on.
  4. Then do up the stem bolts to the torque printed on the stem. The top cap doesn't hold anything once they're tight.

Rules of thumb

RuleWhy
Steerer 3 mm below the top of the stemSo the top cap can pull the bearings together
Spacers under the stem: check the fork maker's limitCarbon steerers often allow 30 to 40 mm
Spacers above the stem: 5 mm or lessMany makers allow one spacer on top, no more
Carbon steerers need an expanding plugNot a star nut, which cuts into carbon
Cut with a guide and a fine sawCarbon with a carbon blade, and a mask

Every fork maker sets its own limits. Check your fork's manual; one well-known maker allows 40 mm under the stem and 5 mm above.

Each spacer

HeightBar moves
5 mmabout 5 mm
10 mmabout 10 mm

Up and slightly back.

Tools

  • Allen keys
  • Torque wrench
  • Steerer cutting guide and saw (for cutting)
  • Carbon paste for a carbon steerer

Things that catch people out

  • Measure twice, cut once. A cut steerer can't be made longer. Ride it a few weeks first.
  • The bars move back as they go up, because the steerer leans back. Your reach gets a little shorter.
  • A knock when you brake usually means the top cap preload needs setting again.
  • Lining the stem up by eye is fine; check it against the front wheel from above.

From the workshop

If you're not sure how high you want the bars, move one spacer at a time and ride it for a week. Only cut the steerer when you've stopped changing your mind. I'll cut a carbon steerer for you if you'd rather not.

Michael

Book it in

Spacers and top caps in the shop

See them all

Not sure which fits? Send us your bike's make, model and year and we'll tell you.

Get the printable PDF

The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.

We'll email you a link. It unlocks every guide on that device.

Already unlocked on this device? Download the PDF

This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against fork makers' published spacer limits.

BookMy Shed