Skip to content

Contact points 7.01

Pedal threads

The left pedal has a reverse thread, so it undoes the opposite way to almost every other bolt. That catches out nearly everyone the first time. Remember this: each pedal tightens forwards, the way the wheel turns.

Get the printable PDF
RIGHT: DRIVE SIDETIGHTENS CLOCKWISEnormal threadLEFT: NON-DRIVE SIDETIGHTENS ANTICLOCKWISEreverse thread, marked L9/16" X 20 TPI1/2" on one-piece and kids' cranksTRAVERSCanewdon, Essextraversbikes.comPEDAL THREADSGUIDE 7.01 · SIZES IN MM · NOT TO SCALE
Seen from each side, both pedals tighten forwards, in the direction the wheel turns. Drawing not to scale.

Fitting pedals

LL ON THE LEFT, SLOPED THREAD

Find the L and R

Stamped on the axle or the end. The left thread slopes the other way.

15 MM SPANNEROR 6 / 8 MM ALLEN

The right tool

A 15 mm pedal spanner on the flats, or a 6 or 8 mm Allen key in the end of the axle.

GREASE THE THREADS35 TO 55 NM (SHIMANO)

Grease and torque

Grease the threads, start them by hand, then tighten. Shimano say 35 to 55 Nm.

Taking pedals off

  1. Put the bike in the big ring so you don't cut your hand on the teeth if the spanner slips.
  2. Turn the spanner backwards, the opposite way to the wheel turning, on both sides. That's anticlockwise on the right, clockwise on the left.
  3. Push down on the spanner, not up, with the crank pointing forwards. Use your weight, not your arm.
  4. Fitting, do the reverse: start by hand, then turn forwards to tighten.

Threads

SizeFound onNotes
9/16" x 20 TPIAlmost all adult bikesThree-piece cranks
1/2" x 20 TPIBMX, kids' bikes, one-piece cranksSmaller, won't swap
Left pedalEvery bikeReverse thread, marked L

Torque

CrankTorque
Alloy (Shimano)35 to 55 Nm
Carbonthe crank maker's figure

Some carbon cranks ask for less and a washer.

Tools

  • 15 mm pedal spanner
  • 6 or 8 mm Allen key
  • Grease
  • Torque wrench

Things that catch people out

  • Never force a pedal in crooked. It strips the crank thread, and that's a new crank or a thread insert.
  • A stuck pedal undoes with a longer spanner and some penetrating oil left overnight.
  • Carbon cranks may need a washer behind the pedal. Check the crank's instructions.
  • Clicking when you pedal is often a dry or loose pedal thread. Grease it and tighten it.

From the workshop

If you can't remember which way, think forwards: put the spanner on, and turn it the way the front of the wheel goes to tighten, backwards to undo. It works on both sides.

Michael

Book it in

Get the printable PDF

The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.

We'll email you a link. It unlocks every guide on that device.

Already unlocked on this device? Download the PDF

This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against Shimano's pedal dealer manual and Park Tool.

BookMy Shed