Skip to content

Gears and drivetrain 5.07

Chainline

Chainline is how far the chainring sits from the middle of the frame. It should line up with the middle of the cassette, so the chain runs as straight as it can. Get it wrong and the chain rubs, drops, wears fast and makes a racket at the ends of the cassette.

Get the printable PDF
FROM ABOVEFRAME CENTRE LINE52CHAINRINGits middle sets the chainlineCASSETTEthe chain should line up with its middleBOTTOM BRACKETthe spindle sets where the crank sitsREAR / CHAINLINERoad double, 130/14243.5 mmMTB, 142 rear49 mmMTB Boost 14852 mmSRAM T-Type, Super Boost55 mmTRAVERSCanewdon, Essextraversbikes.comCHAINLINEGUIDE 5.07 · SIZES IN MM · NOT TO SCALE
Measured from the frame's centre line to the middle of the chainring. Drawing not to scale, sizes in millimetres.

What it looks like

TOO FAR IN

Too far in

Rubs the chainstay and drops off in the big cogs. Often a non-Boost ring on a Boost bike.

STRAIGHT

Straight

The ring lines up with the middle of the cassette. Quiet across the range.

TOO FAR OUT

Too far out

Noisy and skips in the small cogs, and can drop off the outside.

Measuring it

  1. Check your bike's original spec for the chainline and the ring offset. Many cranks say on the box.
  2. Measure from the seat tube to the middle of the ring, then add half the seat tube's width. That's the distance from the frame centre.
  3. On a double, measure to the point halfway between the two rings.
  4. Compare it with the table. A few mm out is fine. More than that and the ring offset or crank is wrong.

Usual chainlines

BikeRear hubChainline
Road double130 or 142 mm43.5 mm
Mountain bike142 mm49 mm
Mountain bike, Boost148 mm52 mm
SRAM T-Type, Super Boost148 or 157 mm55 mm

From Park Tool and the crank makers. Chainline is usually set by the chainring's offset, not the spindle.

Fixing it

Out byFix
About 3 mmA ring with the right offset
MoreCheck the crank and BB

Tools

  • Vernier callipers or a ruler
  • A straight edge or a long ruler

Things that catch people out

  • Boost and non-Boost rings look the same. The difference is a 3 mm offset. Check the ring's markings.
  • Bottom bracket spacers move the crank, and the chainline with it. Fit them as the maker says for your shell.
  • A 1x chain is never perfectly straight. It runs at an angle at both ends; a good chainline keeps that even.
  • Singlespeeds need it spot on, with no mech to take up a bent run. Within a mm or two.

From the workshop

If a 1x bike drops its chain in the easiest gear, check the ring offset before anything else. A Boost frame with a non-Boost ring is the usual cause, and the fix is just the right ring.

Michael

Book it in

Chainrings in the shop

See them all

Not sure which fits? Send us your bike's make, model and year and we'll tell you.

Get the printable PDF

The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.

We'll email you a link. It unlocks every guide on that device.

Already unlocked on this device? Download the PDF

This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against Park Tool's chainline guide and crank makers' figures.

BookMy Shed