Tyres and tubes 4.06
Setting up tubeless
Tubeless means no inner tube. The tyre seals to the rim and a little sealant inside plugs small holes as you ride. You get fewer punctures and can run lower pressure. Setting it up is mostly about the tape: get that right and the rest is easy.
Get the printable PDFThe three things that go wrong
Tape
Wall to wall, tight, over every spoke hole, with no creases. Most leaks are here.
Valve length
Long enough to stick out past the rim so your pump fits on. Deep carbon rims need long valves.
Seating the bead
The bead has to jump up onto the rim shoulder. You'll hear it go, often with a loud bang.
Setting it up
- Check both are tubeless ready. The tyre says TLR, TR or Tubeless Ready, and so does the rim. If not, stop here.
- Tape the rim. Clean it with alcohol, then two turns of tape, pulled tight, across the whole well. Push the valve through the tape at the valve hole.
- Fit the tyre with the sealant in. Fit one bead and most of the other, pour the sealant into the tyre, then finish fitting it. Soapy water on the beads helps.
- Pump it up, then ride it. Inflate until both beads pop up onto the rim. Then go for a ride: it spreads the sealant and makes sure the tyre is properly seated.
How much sealant
From our tyre fit calculator, which uses Silca's and Squirt's own fill guides. Per tyre, in ml.
| Tyre | Silca each | Silca first fill | Squirt each |
|---|---|---|---|
| 700 x 28 road | 55 | 85 | 65 |
| 700 x 40 gravel | 80 | 110 | 75 |
| 650b x 47 gravel | 90 | 120 | 85 |
| 29 x 2.4 mountain | 125 | 155 | 115 |
| 27.5 x 2.4 mountain | 120 | 150 | 95 |
| 26 x 4.5 fat | 205 | 235 | 205 |
The first fill is more because a new tyre soaks some up. Any size: traversbikes.com/tyre-fit
Tape width
| Inner rim width | Tape |
|---|---|
| 19 to 21 mm | 21 to 25 mm |
| 25 mm | 27 to 30 mm |
| 30 mm | 32 to 35 mm |
| 35 mm | 37 to 40 mm |
Inner width plus 2 to 5 mm. The rim maker's own advice comes first.
Tools
- Tubeless tape and valves
- Valve core tool
- Sealant syringe or injector
- Track pump, or a tubeless inflator
- Isopropyl alcohol and a rag
Things that catch people out
- Sealant dries out. Silca say refresh it every 6 months. Shake the wheel by your ear: no slosh, no sealant.
- Valve cores clog. Sealant dries in them. Take the core out and clean it, or swap it, when air won't go in.
- Hookless rims have lower pressure limits. Only fit tyres the rim maker approves, and stay under their maximum.
- Carry a plug kit. Sealant won't close a big cut. A plug usually will, without taking the tyre off.
From the workshop
If a tyre won't seat, take the valve core out and use a tubeless inflator, and put soapy water on both beads. If it still won't, the tape is usually the problem: one more turn of tape makes the rim a fraction bigger and the bead grips. I set up tubeless in the workshop if you'd rather not.
Michael
Book it inTubeless parts in the shop
See them allNot sure which fits? Send us your bike's make, model and year and we'll tell you.
Get the printable PDF
The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.
Already unlocked on this device? Download the PDF
This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against Silca's and Squirt's fill guides, Schwalbe and Stan's tape advice.


