Skip to content

Frames 1.08

Derailleur hangers and UDH

The hanger is the small metal part that joins your rear derailleur to the frame. It's made to bend, or snap, in a crash so the frame and the mech don't. Most frames used a hanger of their own shape, which made finding a spare hard. SRAM's UDH (Universal Derailleur Hanger) fixed that.

Get the printable PDF
A FRAME'S OWN HANGERfrom the drive sideCHAINSTAYSEATSTAYHANGERscrewed to the dropoutMECH BOLT THREADM10 x 1, the same on every hangerDROPOUTthe end of the frameSRAM UDHfrom the drive sideCHAINSTAYSEATSTAYSTOP TAB (HIDDEN)lets it swing back in a crashUDH BOLT8 mm hex, reverse threadHANGERinside the dropout, round the axleUDH, CUTfrom behindAXLEthe axle screws into the boltTRAVERSCanewdon, Essextraversbikes.comDERAILLEUR HANGERS AND UDHGUIDE 1.08 · SIZES IN MM · NOT TO SCALE
A frame's own hanger and a SRAM UDH on real dropouts, from the drive side, and the UDH cut through the axle. Hidden parts are dashed. Drawing not to scale.

Three ways a mech is held

MADE FOR ONE FRAME

The frame's own hanger

A flat plate screwed to the outside of the dropout with one or two small screws. Made for one frame, or a few.

UDH: ONE SHAPE, MANY FRAMES

SRAM UDH

Sits on the inside of the dropout round the axle, held by a hollow bolt from outside. The thru-axle screws into that bolt.

T-TYPE: NO HANGER, ON THE AXLE

No hanger (T-Type)

SRAM Transmission clamps straight onto a UDH frame round the axle. No hanger to bend, and no hanger to set straight.

Finding and fitting a hanger

  1. Check your bike's original spec or the frame maker's website for the hanger part number. A UDH frame says so, and the hanger has UDH on it.
  2. Or match the old one against a hanger chart: the shape, the number of screws, the axle hole and the thread all have to match.
  3. Fitting a UDH: seat it inside the dropout, turn it forward against its stop tab, then do up the UDH bolt from the outside. It's a reverse thread.
  4. Check it's straight with a hanger alignment gauge, then set the gears up again from the start.

UDH at a glance

PartDetail
Where it sitsInside the dropout, round the thru-axle
UDH boltHollow, 8 mm hex, reverse thread, from the outside
Bolt torqueAbout 25 Nm; check the frame or hanger maker
Thru-axleM12 x 1.0, screws into the UDH bolt
Mech bolt threadM10 x 1, the same as every hanger
Stop tabLets it swing back in a crash instead of bending the frame

From SRAM's UDH information and Wolf Tooth's UDH instructions.

Signs of a bent hanger

You noticeWhy
Gears won't indexMech not parallel to the cogs
Jumps on some cogsBent in or out
Mech near the spokesBent in: stop riding

Tools

  • Allen keys or Torx keys to suit
  • Hanger alignment gauge (or leave it to the workshop)
  • Torque wrench

Things that catch people out

  • The UDH bolt is a reverse thread. Turn it the opposite way to normal to undo it, or you'll be tightening it.
  • Don't bend a hanger back more than once. Alloy work-hardens and can snap. Fit a new one.
  • Don't lay the bike on its drive side. It's the easiest way to bend a hanger.
  • Carry a spare on long trips, unless it's UDH, which most shops have. A snapped hanger with no spare means a singlespeed ride home.

From the workshop

If your gears won't settle however much you fiddle with the barrel adjuster, check the hanger before anything else. Straightening one with a proper gauge is a quick workshop job, so book it in if you don't have one.

Michael

Book it in

Frame spares in the shop

See them all

Not sure which fits? Send us your bike's make, model and year and we'll tell you.

Get the printable PDF

The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.

We'll email you a link. It unlocks every guide on that device.

Already unlocked on this device? Download the PDF

This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against SRAM's UDH and Full Mount information and Wolf Tooth's UDH instructions.

BookMy Shed