Frames 1.06
Dropper post sizing
A dropper post has to match three things: the size of your seat tube, how high your saddle sits, and how far the post can go into the frame. Get the last two wrong and you either can't get the saddle high enough or the post won't go in. Two measurements sort it.
Get the printable PDFCables and travel
Cable inside the frame
Most droppers now. The cable goes into the bottom of the post, so the frame needs a port for it.
Cable outside
The cable fixes at the collar. For frames with no internal routing. Fewer to choose from now.
Travel shims
Many droppers can be cut down 10 or 20 mm with shims inside, so a longer post can fit a smaller frame.
Which dropper fits?
- Check your bike's original spec for the seatpost diameter, often 30.9, 31.6 or 34.9 mm. Or read it on your old post, near the minimum insert line.
- Measure X, your ride height, with the saddle where you pedal: from the top of the seat clamp to the middle of the saddle rails.
- Measure Y, the insertion depth. Take the post out, drop a rod or tape in until it stops, and measure from the top of the clamp. Take 10 to 15 mm off.
- Find the longest travel that fits both. The post below the collar must fit inside Y, and the collar plus head must sit below X. Makers' calculators do the sums for you.
What the numbers mean
| Measurement | What it is | How it decides the post |
|---|---|---|
| Diameter | Inside of your seat tube | Must match exactly: 30.9, 31.6, 34.9 mm |
| X, ride height | Top of the seat clamp to the middle of the rails | Collar, head and travel all have to fit under it |
| Y, insertion depth | Top of the seat clamp to the first obstruction | The post below the collar has to fit inside it |
| Travel | How far the saddle drops | Usually 100 to 240 mm; longer needs more of X and Y |
| Stack height | Collar plus the head, with the post down | Differs between makers, so check theirs |
Method from OneUp Components' own sizing guide. Every maker lists its own lengths, so put your X and Y into theirs.
Rough travel by rider height
| Rider | Travel |
|---|---|
| Under 5' 6" | 100 to 150 mm |
| 5' 6" to 5' 11" | 150 to 180 mm |
| 6' and over | 180 to 240 mm |
A guide only. X and Y decide it.
Tools
- Tape measure
- A thin rod or old spoke for the insertion depth
- Allen keys or a torque wrench for the seat clamp
- Cable cutters
Things that catch people out
- Measure to the first obstruction, not the bottom bracket. A bend, an internal weld, a bottle cage bolt or a suspension pivot all stop the post.
- Leave room for the cable. Pushing the post all the way down can kink the cable, which is why the 10 to 15 mm comes off.
- Shims don't change the diameter. A 30.9 post in a 31.6 frame can use a shim, but the maker has to approve it for a dropper.
- The lever needs a place on the bar, on the left where the front shifter used to be on a 1x bike.
From the workshop
Measure twice before you order. A post that's 20 mm too long to go in means less drop than you paid for, or no ride at all until it's swapped. If you'd like, bring the bike in and I'll measure it and fit the post.
Michael
Book it inSeatposts in the shop
See them allNot sure which fits? Send us your bike's make, model and year and we'll tell you.
Get the printable PDF
The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.
Already unlocked on this device? Download the PDF
This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against OneUp Components' dropper sizing guide.
