Frames 1.01
Headsets explained
Headset sizes can be confusing and tricky to understand. This is a straightforward guide to help lift the mystery: what the codes mean, and how to work out which headset your bike takes before you order one.
Get the printable PDFThe three types
EC: external cup
The cup sits on top of the head tube and you can see all of it. Common on older steel bikes.
ZS: zero stack
The cup is pressed inside the head tube. Only a thin lip shows at the top.
IS: integrated
No cup. The bearing drops straight onto an angled seat in the frame. Common on carbon frames.
Which one have I got?
- Check your bike's original spec. Look up your model and year on the bike maker's website, or check the spec sheet or receipt from when it was bought. Many list the headset code. Measure anyway if the bike has had a new fork or headset since.
- Look at the top of the head tube and match it to one of the three types above.
- Take the fork out and measure inside the head tube, top and bottom, with callipers. Take out the cups and bearings first, and measure at the very edge. Deeper in, the angled seats give a false reading.
- Measure the steerer at the top and just above the crown. The same at both ends means straight. Wider at the bottom means tapered.
Reading the code
A headset has a code for the top and a code for the bottom, shown with a bar between them. Each one gives the type, the size of the hole in the frame, then the fork size.
ZS44/28.6|ZS56/40
- ZS44
- Zero stack cup for a 44 mm hole at the top of the head tube
- /28.6
- Steerer is 28.6 mm at the top, which is 1 1/8"
- ZS56
- Zero stack cup for a 56 mm hole at the bottom
- /40
- Crown race for a 1.5" fork. The bottom number is the crown race size, not the steerer. /30 means a 1 1/8" fork.
Common headsets
| Code (top | bottom) | What it is | You'll often find it on |
|---|---|---|
| EC34/28.6 | EC34/30 | Straight 1 1/8", cups outside | Steel frames, older bikes |
| ZS44/28.6 | ZS44/30 | Straight 1 1/8", cups inside | Alloy frames with straight forks |
| ZS44/28.6 | ZS56/40 | Tapered, cups inside | Most modern mountain bikes, many gravel bikes |
| ZS44/28.6 | EC44/40 | Tapered fork, straight 44 mm head tube | Fitting a tapered fork to an older frame |
| IS42/28.6 | IS52/40 | Tapered, bearings straight into the frame | Carbon road and gravel bikes |
| IS41/28.6 | IS52/40 | As above, with different top bearings | Some carbon road bikes |
What your callipers will read
| Code | Hole in the frame (mm) |
|---|---|
| EC34 | 33.80–33.95 |
| ZS44 | 43.90–43.95 |
| ZS49 | 49.57–49.65 |
| ZS56 | 55.90–55.95 |
| IS41 | 41.10–41.20 |
| IS42 | 41.95–42.05 |
| IS52 | 52.10–52.15 |
The number in the code is rounded, so a ZS44 frame measures just under 44.
Tools
- Vernier or digital callipers
- Headset press
- Cup remover
- Crown race setter and remover
Things that catch people out
- IS41 and IS42 look almost the same. IS41 bearings are 41 mm across with 36° × 45° angles. IS42 bearings are 41.8 mm with 45° × 45°. The wrong one will sit badly and wear out fast.
- The bottom number isn't the steerer size. A 1.5" steerer is 38.1 mm, but its code is 40 because the crown race seat is 39.8 mm.
- A new fork can mean a new headset. Going from a straight fork to a tapered one needs a different bottom cup or crown race, and may not fit the frame at all.
- Some brands use their own sizes. If nothing here matches, check with the bike maker or ask us.
From the workshop
Before you order a headset, take the old one out and measure it. What the bike maker says isn't always what's in the frame, especially on older bikes or ones that have had a new fork. If you're not sure, bring it in and we'll measure it for you.
Michael
Book it inHeadsets in the shop
See them allNot sure which fits? Send us your bike's make, model and year and we'll tell you.
Get the printable PDF
The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.
Already unlocked on this device? Download the PDF
This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 16/11/2026 against Park Tool and Cane Creek published specs.

