Skip to content

Frames 1.02

Measuring for a headset

Guide 1.01 explains the headset codes. This one is how to measure your bike so you know which code it takes. You need a pair of callipers, the fork out, and the old cups and bearings out of the frame.

Get the printable PDF
1 BORE: INSIDE JAWS43.90 = ZS44HEAD TUBEcups and bearings outMeasure at the very edge, top and bottom2 STEERER: OUTSIDE JAWS28.6 TOP39.8 CROWN RACE SEATCROWN RACEsits on the seatTRAVERSCanewdon, Essextraversbikes.comMEASURING FOR A HEADSETGUIDE 1.02 · SIZES IN MM · NOT TO SCALE
Inside jaws read the head tube bore; outside jaws read the steerer. Drawing not to scale, sizes in millimetres.

Three things to measure

TOP AND BOTTOM

Head tube bore

Top and bottom, right at the edge. Deeper in, an angled bearing seat gives a false reading.

SAME BOTH ENDS:STRAIGHTWIDER LOW:TAPERED

Steerer

At the top and just above the crown. Same both ends is straight, wider at the bottom is tapered.

1.5" CROWN RACEREDUCER

Crown race seat

39.8 mm on a 1.5" tapered fork, 30.0 mm on 1 1/8". A reducer race fits a tapered fork to a smaller bottom cup.

Measuring, step by step

  1. Check your bike's original spec first. Many makers list the headset code. Then measure anyway, in case it's been changed.
  2. Take the fork out and the cups and bearings out. Note which way round everything came out.
  3. Measure the bore at the top and bottom with the inside jaws, across the widest point, at the very edge. Turn the callipers and measure twice.
  4. Measure the steerer and crown race seat with the outside jaws, and match the readings to the table over the page.

What your callipers will read

CodeBore in the frameCodeBore in the frame
EC3433.80-33.95IS4141.10-41.20
ZS4443.90-43.95IS4241.95-42.05
ZS4949.57-49.65IS5252.10-52.15
ZS5655.90-55.95

In mm, the same figures as guide 1.01. The number in the code is rounded, so a ZS44 frame measures just under 44.

Steerer

ReadingMeans
28.61 1/8" top
31.81 1/4" (rare)
38.11.5" bottom
39.8 seat1.5" crown race
30.0 seat1 1/8" crown race

Tools

  • Vernier or digital callipers
  • Cup remover
  • Crown race remover
  • Rag and degreaser

Things that catch people out

  • IS41 and IS42 are 1 mm apart. Measure carefully and check the bearing angle too: 36° or 45°.
  • Paint and dirt change the reading. Clean the bore first and measure bare metal.
  • Some frames use their own sizes. If nothing matches, check with the frame maker or ask us.
  • The crown race seat isn't the steerer size. A 1.5" steerer has a 39.8 seat, code 40.

From the workshop

Take a photo of the old headset parts before they go in the bin; the bearing usually has its size printed on it. If you're not sure, bring the frame and fork in and I'll measure them for you.

Michael

Book it in

Headsets in the shop

See them all

Not sure which fits? Send us your bike's make, model and year and we'll tell you.

Get the printable PDF

The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.

We'll email you a link. It unlocks every guide on that device.

Already unlocked on this device? Download the PDF

This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against Park Tool and Cane Creek published sizes.

BookMy Shed