Skip to content

Threads, torque and grease 8.01

Torque settings

Most bike bolts have a number printed next to them, like 5 Nm. That's how tight they should be. Too loose and parts slip or rattle, too tight and you crack carbon or strip threads. A small torque wrench takes the guessing out of it.

Get the printable PDF
1234561STEM FACEPLATEabout 5 Nm2STEM STEERER BOLTSabout 5 Nm3SEAT CLAMPabout 5 to 6 Nm, less on carbon4THRU-AXLEcheck the fork, often 12 to 15 Nm5BRAKE CALIPER BOLTS6 to 8 Nm6PEDALS35 to 55 Nm (Shimano)Typical figures only. Always use the number printed on the part.TRAVERSCanewdon, Essextraversbikes.comTORQUE SETTINGSGUIDE 8.01 · SIZES IN MM · NOT TO SCALE
The bolts you'll do up most often, with typical torques. Always use the number printed on the part.

Doing it right

SET IT, PULL UNTIL IT CLICKS

Torque wrench

Set the number, then pull smoothly until it clicks. Stop at the click.

1234CROSSWISE, A LITTLE AT A TIME

Crosswise

Faceplates and clamps with several bolts: a little at a time, crosswise, keeping the gaps even.

CARBONPASTE

Carbon paste

On carbon parts, carbon assembly paste lets them grip at a lower torque.

Reading the numbers

  1. Look on the part first. The torque is usually printed next to the bolt, like "5 Nm max" or "4-6 Nm".
  2. Use the lowest number that works on carbon. Go up only if it slips, and never past the maximum.
  3. Two parts, two numbers? Use the lower one. A carbon bar in an alloy stem: the bar's number.
  4. No number anywhere? Check the maker's manual online, then use the typical figures over the page.

Typical torques

PartTypicalCheck
Stem faceplate and steerer bolts5 NmPrinted on the stem
Seat clamp5 to 6 NmLess on carbon posts
Brake caliper bolts6 to 8 NmBrake maker's manual
Rotor bolts, 6-boltSRAM 6.2, Shimano 2 to 4 NmRotor maker
Centerlock lockring40 NmPrinted on the lockring
Cassette lockringabout 40 NmPrinted on the lockring
Shimano crank pinch bolts12 to 14 NmDo them up in turn
Pedals35 to 55 Nm (Shimano)Crank maker on carbon
Bottle cage boltsabout 4 NmEasy to strip

Typical figures from makers' manuals and Park Tool. The number on your part always wins.

Things that catch people out

  • Grease changes the torque. Grease threads unless the maker says threadlock, and use their number.
  • Don't use a torque wrench to undo bolts. It upsets the calibration.
  • Small bolts strip easily. 4 to 5 Nm is not much: two fingers on a short Allen key.
  • Check bolts again after the first ride on new parts. Some settle in.

Tools

  • Torque wrench, about 2 to 15 Nm
  • Bit set to suit
  • Carbon assembly paste
  • Grease

From the workshop

A small torque wrench is the second tool I'd buy after a pump. Carbon bars, posts and steerers can crack if they're overtightened, and that's an expensive mistake to make for the sake of a tool.

Michael

Book it in

Get the printable PDF

The same guide on two A4 pages, to print for the workshop or keep on your phone. Leave your email and we'll send the link. It unlocks every guide in the library on that device.

We'll email you a link. It unlocks every guide on that device.

Already unlocked on this device? Download the PDF

This guide is general advice for home mechanics. Bikes and parts vary, so always follow the maker's instructions and torque settings for your parts. If you're not sure, or the job needs tools you don't have, ask a qualified mechanic. Travers Bikes can't be responsible for work you carry out yourself. Nothing here affects your legal rights. Sizes checked 17/11/2026 against makers' torque figures and Park Tool's torque table.

BookMy Shed